INDUSTRIAL SURFACE

SportMaster · Technical data sheet

LevelMaster with Sand

LevelMaster with Sand is an asphalt emulsion resurfacer for new or uncoated asphalt that reduces surface porosity before SportMaster color finish systems. The sheet gives a coating mix (10 gallons of LevelMaster with Sand, 3 gallons of water) and a patching mix for lifts up to 1/4” with 20-40 mesh sand, Portland cement, water and Asphalt Binder. Coverage typically averages about .13 gallons per square yard, and each coat dries in 30 - 60 minutes, with at least 6 hours before a second coat.

CMT-31 Revised December 2019 2 pages, 127 KB

Open the PDF Ask us about it

This is SportMaster's document, kept here so our customers and crews can read it beside our own pages. SportMaster's own copy is on sportmaster.net.

First page of the SportMaster technical data sheet for LevelMaster with Sand Open the PDF (2 pages, 127 KB)

Key facts

UseNew or uncoated asphalt, before SportMaster color finish systems
Coating mixLevelMaster with Sand 10 gallons, Water 3 gallons
Patching mixLevelMaster with Sand 10 gallons, Sand (20-40 mesh) 80-120 pounds, Portland Cement 8 pounds, Water 1-3 gallons, Asphalt Binder 1 gallon
CoverageAbout .13 gallons per square yard
Drying time30 - 60 minutes; at least 6 hours of cure before a second coat
Application temperatureSurface and air above 50°F (10°C) during application and for at least 24 hours after

Taken from this document. The PDF is SportMaster's official document (CMT-31, revised December 2019).

The full text of this document

This is the document's own text, moved from the PDF by machine, word for word, and checked against it. The PDF is SportMaster's official document (CMT-31, revised December 2019). If the two ever differ, the PDF is right.

REVISED 12/19 · Technical Data Sheet · LEVELMASTER WITH SAND · CMT-31

PRODUCT DESCRIPTION & BENEFITS

LevelMaster with Sand is an asphalt emulsion resurfacer designed for on site mixing with silica sand and water. LevelMaster with Sand reduces surface porosity allowing for application of an even, full depth color, playing surface.

USES

LevelMaster With Sand is applied to new or uncoated asphalt surfaces in preparation for SportMaster color finish systems.

COLOR

Black.

SURFACE PREPARATION

Pavement surface must be cleaned entirely of dust, dirt, debris and all loose materials. New asphalt must cure 14-30 days before application. Repair of pavement surface defects, depressions and cracks must be completed prior to application. All repairs must be flush and smooth to adjoining surfaces.

MIXING PROCEDURES

For Use As A Coating - Use the following mix design to produce a smooth, free flowing mixture (Based on 10 gallons of LevelMaster with Sand for ease of calculation):

LevelMaster with Sand10 gallons
Water3 gallons

For Use As A Patching Material - LevelMaster with Sand may be modified with the following mix design for applications up to 1/4” lifts:

LevelMaster with Sand10 gallons
Sand (20-40 mesh)80-120 pounds
Portland Cement8 pounds

Always mix cement thoroughly with a small amount of water before adding to patching mix.

Water1-3 gallons
Asphalt Binder1 gallon

APPLICATION

Apply LevelMaster with Sand with a soft rubber squeegee. Apply successive coats in cross directions. Scrape all rough spots and ridges before applying the next coat.

IMPORTANT

Surface and air temperatures must be above 50°F (10°C) during application and for at least 24 hours after application. Stir before using. Do not apply when rain is imminent or forecast. Keep from freezing. Close container when not in use.

Product Data

TypeAcrylic Emulsion
Pounds per gallon at 77°F11.87 ± .5 lbs.
OdorAsphalt
FlammabilityNon-Flammable
Flash PointNone

COVERAGE

Yield calculations are based on undiluted gallons of LevelMaster with Sand and vary according to surface texture and porosity. Coverage rates will typically average about .13 gallons per square yard.

DRYING TIME

30 - 60 minutes under optimum drying conditions. Allow at least 6 hours of cure time before applying a second coat of LevelMaster.

CAUTIONS

Do not store in direct sunlight or where temperatures exceed 100°F. Do not apply if rain is imminent or forecast. Keep from freezing. Close container when not in use. Refer to product Safety Data Sheet (SDS) for additional safety information and precautions.

WARRANTY

The statements made on this technical bulletin are believed to be true and accurate, and are intended to provide a guide for approved construction practices. Manufacturer does not make, nor does it authorize any agent or representative to make any warranty, express or implied, concerning this material as workmanship, weather, construction, equipment utilized and other variables affecting results are all beyond our control. Manufacturer warrants only that the material conforms to product specifications and any liability to the buyer or user of this product is limited to the replacement value of the product only. In no event shall Manufacturer be liable for any injury, loss or damage, either direct or incidental, special or consequential, however arising, in connection with material or equipment furnished or work performed. Manufacturer shall not, in any manner, be liable for any defects, variations or change in condition in the substructure over which its products are installed.

Page 2

Copyright© 2019, SportMaster
All rights reserved.

ThorWorks Industries, Inc.
P.O. Box 2277
Sandusky, OH 44870

Phone: 1-800-326-1994 FAX: 1-419-626-5477 www.sportmaster.net

Free estimates

Planning a court or a surface?

Industrial Surface is a SportMaster authorized installer in Northeast Ohio. Send the address and what you have in mind; we walk the site, measure it, and send a written proposal with the scope spelled out.

The yard

4000 East 86th Street, Cleveland, OH 44105

Off Broadway Avenue, south of downtown, ten minutes from I-77 and I-490.

Serving Cuyahoga, Summit, Lake, Lorain, Medina, Geauga, Portage, Stark and Ashtabula counties. Municipal, school, club, HOA and commercial work; residential courts by the job.