INDUSTRIAL SURFACE

SportMaster · Technical data sheet

Acrylic Resurfacer with Sand

Acrylic Resurfacer With Sand is a 100% acrylic emulsion with the sand already in it, for filling and smoothing asphalt or concrete before SportMaster color coating systems. The sheet gives a patch mix for filling depressions (10 gallons of resurfacer, 3 gallons of water, 40 pounds of sand, 1 gallon of cement) with screeding steps, and two coating mixes: 55 gallons with 22 gallons of water, or 30 gallons with 12 gallons of water. Each coat requires .11 to .13 gallons per square yard and dries in 30 to 60 minutes.

CMT-33 Revised December 2019 2 pages, 123 KB

Open the PDF Ask us about it

This is SportMaster's document, kept here so our customers and crews can read it beside our own pages. SportMaster's own copy is on sportmaster.net.

First page of the SportMaster technical data sheet for Acrylic Resurfacer with Sand Open the PDF (2 pages, 123 KB)

Key facts

UseTennis, basketball and pickleball courts and other asphalt or concrete surfaces
Coating mix (drum)Drum Mix 55 gallons, Water 22 gallons
Coating mixAcrylic Resurfacer with Sand 30 gallons, Water 12 gallons
Coverage.11 to .13 gallons per square yard, each coat
Drying time30 to 60 minutes under optimum drying conditions
Application temperatureSurface and air above 50°F (10°C) during application and for at least 24 hours after

Taken from this document. The PDF is SportMaster's official document (CMT-33, revised December 2019).

The full text of this document

This is the document's own text, moved from the PDF by machine, word for word, and checked against it. The PDF is SportMaster's official document (CMT-33, revised December 2019). If the two ever differ, the PDF is right.

REVISED 12/19 · Technical Data Sheet · ACRYLIC RESURFACER WITH SAND · CMT-33

PRODUCT DESCRIPTION & BENEFITS

SportMaster Acrylic Resurfacer With Sand is a 100% acrylic emulsion with sand designed for filling and smoothing asphalt or concrete surfaces in preparation for SportMaster color coating systems.

USES

Tennis courts, basketball courts, pickleball courts, and other asphalt or concrete surfaces.

COLOR

Black.

Product Data

OdorSlight Ammonia
FlammabilityNon-Flammable
Flash PointNone
Storage LifeOne Year
ColorsBlack

SURFACE PREPARATION

Asphalt: New asphalt surfaces must cure 14-30 days prior to application. Pavement surface must be cleaned entirely of dust, dirt, debris and all loose materials. Repair of pavement surface defects, depressions and cracks should be complete prior to application.

Concrete: New concrete surfaces must cure 28 days prior to application. Concrete surfaces should have a medium broom finish or similar roughened texture. Etch surface with phosphoric or muriatic acid and rinse thoroughly with water. Allow concrete to dry completely before applying Acrylic Adhesion Promoter.

MIXING PROCEDURES

Patching: For Patching and filling depressions, Acrylic Resurfacer With Sand may be modified with sand and cement using the following mix design:

Acrylic Resurfacer with Sand10 gallons
Water3 gallons
Sand40 pounds
Cement1 gallon

(always mix cement thoroughly with a small amount of water before adding to patch mix).

For applying patch mix, you’ll need a straight edge or screed bar (Metal, wooden, aluminum, etc.) that is wider than the depression area that will be patched. Apply large amount of patch material at one end of the depression and use the straight edge to screed and smooth material across the depression. Feather the edges of the patch material with a hand trowel or squeegee to assure a smooth patch. Allow patch to cure 24 hours. If shrinkage cracks occur when patch dries, simply apply another coat of patch mix with a squeegee. This will fill in and eliminate shrinkage cracks. Once patch mix has thoroughly cured (atleast 24 hours) sanding or grinding may be required to provide a smooth patch finish.

Coating: When applying Acrylic Resurfacer With Sand as a coating, use the following mix design:

Drum Mix55 gallons
Water22 gallons
Acrylic Resurfacer with Sand30 gallons
Water12 gallons

Apply Acylic Resurfacer With Sand as a coating using a soft rubber squeegee. Allow to dry. Scrape all rough spots and ridges before applying the next coat. Apply one or two coats, depending on surface porosity and condition. Two coats are recommended on new or uncoated asphalt.

IMPORTANT

Surface and air temperatures must be above 50°F (10°C) during application and for at least 24 hours after application. Stir before using. Do not apply when rain is imminent or forecast. Keep from freezing. Close container when not in use.

DRYING TIME

30 to 60 minutes under optimum drying conditions.

COVERAGE

Yield calculations are based on undiluted gallons of SportMaster Acrylic Resurfacer With Sand and will vary according to surface texture and porosity within the limits below: Each coat requires .11 to .13 gallons per square yard.

CAUTIONS

Do not store in direct sunlight or where temperatures exceed 100°F. Do not apply if rain is imminent or forecast. Keep from freezing. Close container when not in use. Refer to product Safety Data Sheet (SDS) for additional safety information and precautions.

WARRANTY

The statements made on this technical bulletin are believed to be true and accurate, and are intended to provide a guide for approved construction practices.

Page 2

Manufacturer does not make, nor does it authorize any agent or representative to make any warranty, express or implied, concerning this material as workmanship, weather, construction, equipment utilized and other variables affecting results are all beyond our control. Manufacturer warrants only that the material conforms to product specifications and any liability to the buyer or user of this product is limited to the replacement value of the product only. In no event shall Manufacturer be liable for any injury, loss or damage, either direct or incidental, special or consequential, however arising, in connection with material or equipment furnished or work performed. Manufacturer shall not, in any manner, be liable for any defects, variations or change in condition in the substructure over which its products are installed.

Copyright© 2019, SportMaster
All rights reserved.

ThorWorks Industries, Inc.
P.O. Box 2277
Sandusky, OH 44870

Phone: 1-800-326-1994 FAX: 1-419-626-5477 www.sportmaster.net

Free estimates

Planning a court or a surface?

Industrial Surface is a SportMaster authorized installer in Northeast Ohio. Send the address and what you have in mind; we walk the site, measure it, and send a written proposal with the scope spelled out.

The yard

4000 East 86th Street, Cleveland, OH 44105

Off Broadway Avenue, south of downtown, ten minutes from I-77 and I-490.

Serving Cuyahoga, Summit, Lake, Lorain, Medina, Geauga, Portage, Stark and Ashtabula counties. Municipal, school, club, HOA and commercial work; residential courts by the job.