INDUSTRIAL SURFACE

SportMaster · Technical data sheet

CourtFlex

CourtFlex is an elastomeric cold pour crack sealant for cracks up to 1/2” wide on asphalt and concrete sport and recreational pavement; the sheet says it keeps its flexibility, elasticity and adhesion at temperatures as low as -15°F. It is poured as is into cleaned cracks, with deep cracks first filled with sand or backer rod to within 3/4” of the surface. Coverage is approximately 150-200 linear feet of 1/2” wide x 1/2” deep cracks. It comes in green, red and neutral.

CMT-8 Revised December 2019 1 page, 70 KB

Open the PDF Ask us about it

This is SportMaster's document, kept here so our customers and crews can read it beside our own pages. SportMaster's own copy is on sportmaster.net.

First page of the SportMaster technical data sheet for CourtFlex Open the PDF (1 page, 70 KB)

Key facts

UseCracks up to 1/2” wide on sport and recreational pavement
ApplicationUse as is, do not dilute; pour into the crack until filled
Deep cracksFill with sand or backer rod to within 3/4” of the surface
CoverageApproximately 150-200 linear feet of 1/2” wide x 1/2” deep cracks
Application temperatureSurface not expected to drop below 50°F or exceed 120°F
ColorsGreen, red and neutral

Taken from this document. The PDF is SportMaster's official document (CMT-8, revised December 2019).

The full text of this document

This is the document's own text, moved from the PDF by machine, word for word, and checked against it. The PDF is SportMaster's official document (CMT-8, revised December 2019). If the two ever differ, the PDF is right.

REVISED 12/19 · Technical Data Sheet · COURTFLEX · CMT-8

PRODUCT DESCRIPTION & BENEFITS

An elastomeric cold pour crack sealant designed for use in cracks on sport and recreational pavement surfaces. Use to seal cracks up to 1/2” in width. Maintains excellent flexibility, elasticity and adhesion at temperatures as low as -15°F on asphalt and concrete surfaces.

USES

Tennis courts, basketball courts, pickleball courts, and other athletic and recreational areas.

COLOR

Available in green, red, and neutral colors.

SURFACE PREPARATION

Cracks must be cleaned of dust, dirt, and debris including vegetation. Blow clean with an air compressor or high pressure washer. Fill deep cracks with sand or backer rod to within 3/4” of surface.

APPLICATION

Use product as is. Do not dilute. Pour into crack until it is filled completely. Set time is dependant upon temperature, humidity and sealer thickness. For best results, apply on dry surface when surface temperature is not expected to drop below 50°F or exceed 120°F. Material must be at or below surface level when application is completed. Before material sets up, scrape excess from surface and use a rubber squeegee surface contour of finished application.

IMPORTANT

Surface and air temperatures must be above 50°F (10°C) during application and for at least 24 hours after application. Stir before using. Do not apply when rain is imminent or forecast. Keep from freezing. Close container when not in use.

COVERAGE

Approximately 150-200 linear feet of 1/2” wide x 1/2” deep cracks.

CLEAN UP

Wash tools in water before material dries.

CAUTIONS

Do not store in direct sunlight or where temperatures exceed 100°F. Do not apply if rain is imminent or forecast. Keep from freezing. Close container when not in use. Refer to product Safety Data Sheet (SDS) for additional safety information and precautions.

WARRANTY

The statements made on this technical bulletin are believed to be true and accurate, and are intended to provide a guide for approved construction practices. Manufacturer does not make, nor does it authorize any agent or representative to make any warranty, express or implied, concerning this material as workmanship, weather, construction, equipment utilized and other variables affecting results are all beyond our control. Manufacturer warrants only that the material conforms to product specifications and any liability to the buyer or user of this product is limited to the replacement value of the product only. In no event shall Manufacturer be liable for any injury, loss or damage, either direct or incidental, special or consequential, however arising, in connection with material or equipment furnished or work performed. Manufacturer shall not, in any manner, be liable for any defects, variations or change in condition in the substructure over which its products are installed.

Copyright© 2019, SportMaster
All rights reserved.

ThorWorks Industries, Inc.
P.O. Box 2277
Sandusky, OH 44870

Phone: 1-800-326-1994 FAX: 1-419-626-5477 www.sportmaster.net

Free estimates

Planning a court or a surface?

Industrial Surface is a SportMaster authorized installer in Northeast Ohio. Send the address and what you have in mind; we walk the site, measure it, and send a written proposal with the scope spelled out.

The yard

4000 East 86th Street, Cleveland, OH 44105

Off Broadway Avenue, south of downtown, ten minutes from I-77 and I-490.

Serving Cuyahoga, Summit, Lake, Lorain, Medina, Geauga, Portage, Stark and Ashtabula counties. Municipal, school, club, HOA and commercial work; residential courts by the job.