INDUSTRIAL SURFACE

SportMaster · Technical data sheet

Flexible Acrylic Resurfacer

Flexible Acrylic Resurfacer is a 100% acrylic, elastomeric emulsion resurfacer, mixed on site with silica sand, for asphalt, concrete or existing acrylic surfaces before SportMaster color finish systems. The sheet says it stays flexible longer than traditional acrylics and suits membrane crack repair systems and cushioned underlayments. It gives the coating mix (55 gallons of resurfacer, 500-600 pounds of 50-60 mesh silica sand, 33 gallons of water), coverage of .07 to .09 gallons per square yard per coat and a drying time of 30 to 60 minutes.

CMT-60 Revised December 2019 2 pages, 126 KB

Open the PDF Ask us about it

This is SportMaster's document, kept here so our customers and crews can read it beside our own pages. SportMaster's own copy is on sportmaster.net.

First page of the SportMaster technical data sheet for Flexible Acrylic Resurfacer Open the PDF (2 pages, 126 KB)

Key facts

UseAsphalt, concrete or existing acrylic surfaces, before SportMaster color finish systems
Coating mixFlexible Acrylic Resurfacer 55 gallons, Silica Sand (50-60 mesh) 500-600 pounds, Water 33 gallons
Coverage.07 to .09 gallons per square yard per coat
Drying time30 to 60 minutes under optimum drying conditions
Application temperatureSurface and air above 50°F (10°C) during application and for at least 24 hours after
ColorNeutral

Taken from this document. The PDF is SportMaster's official document (CMT-60, revised December 2019).

The full text of this document

This is the document's own text, moved from the PDF by machine, word for word, and checked against it. The PDF is SportMaster's official document (CMT-60, revised December 2019). If the two ever differ, the PDF is right.

REVISED 12/19 · Technical Data Sheet · FLEXIBLE ACRYLIC RESURFACER · CMT-60

PRODUCT DESCRIPTION & BENEFITS

SPORTMASTER FLEXIBLE ACRYLIC RESURFACER is a100% acrylic, elastomeric emulsion resurfacer designed for on-site mixing with silica sand. Flexible Acrylic Resurfacer reduces surface porosity allowing for application of an even, full depth color, playing surface. Retextures existing smooth playing surfaces to promote consistent application of successive coats.

USES

SportMaster Flexible Acrylic Resurfacer is applied to asphalt, concrete, or existing acrylic surfaces in preparation for SportMaster color finish systems.

  • Ideal binder for membrane crack repair systems that exhibit stretching and flexing.
  • More compatible with cushioned underlayments and flexible sub-layers.
  • Stays flexible longer than traditional acrylics to maintain softness of cushion systems.

COLOR

Neutral.

Chemical Characteristics

% Weight (minimum)

Acrylic Emulsion44.0
Hiding Pigment2.0
Mineral Inert Fillers5.0
Film Formers, Additives2.0
Water45.0

Product Data

TypeAcrylic Emulsion
Pounds per gallon at 77°F8.5 ± .5
% Non Volatile Material27.5 ± 5.0
OdorSlight Ammonia
FlammabilityNon-Flammable
Flash PointNone
Storage LifeOne Year

SURFACE PREPARATION

Pavement surface must be cleaned entirely of dust, dirt, debris and all loose materials. New asphalt must cure 14-30 days before application. New concrete surfaces must cure 28 days prior to application. Concrete surfaces should have a medium broom finish or similar roughened texture. Etch surface with muriatic or phosphoric acid and apply SportMaster Acrylic Adhesion Promoter (Technical Bulletin CMT - 21). Repair of pavement surface defects, depressions and cracks must be completed prior to application. All repairs must be flush and smooth to adjoining surfaces.

MIXING PROCEDURES

FOR USE AS A COATING - Use the following mix design (based on 55 gallons of Flexible Acrylic Resurfacer for ease of calculation):

Flexible Acrylic Resurfacer55 gallons
Silica Sand (50-60 mesh)500-600 pounds
Water33 gallons

APPLICATION

Apply Flexible Acrylic Resurfacer with a soft rubber squeegee. Apply successive coats in cross directions. Scrape all rough spots and ridges before applying the next coat. Apply one or two coats, depending on surface porosity and condition. Two coats are recommended on new or uncoated asphalt.

IMPORTANT

Surface and air temperatures must be above 50°F (10°C) during application and for at least 24 hours after application. Stir before using. Do not apply when rain is imminent or forecast. Keep from freezing. Close container when not in use.

DRYING TIME

30 to 60 minutes under optimum drying conditions.

COVERAGE

Yield calculations are based on undiluted gallons of SportMaster Flexible Acrylic Resurfacer and will vary according to surface texture and porosity within the limits below: .07 to .09 gallons per square yard per coat.

CAUTIONS

Do not store in direct sunlight or where temperatures exceed 100°F. Do not apply if rain is imminent or forecast. Keep from freezing. Close container when not in use. Refer to product Safety Data Sheet (SDS) for additional safety information and precautions.

WARRANTY

The statements made on this technical bulletin are believed to be true and accurate, and are intended to provide a guide for approved construction practices. Manufacturer does not make, nor does it authorize any agent or representative to make any warranty, express or implied, concerning this material as workmanship, weather, construction, equipment utilized and other variables affecting results are all beyond our control. Manufacturer warrants only that the material conforms to product specifications and any liability to the buyer or user of this product is limited to the replacement value of the product only. In no event shall Manufacturer be liable for any injury, loss or damage, either direct or incidental, special or consequential, however arising, in connection with material or equipment furnished or work performed. Manufacturer shall not, in any manner, be liable for any defects, variations or change in condition in the substructure over which its products are installed.

Page 2

Copyright© 2019, SportMaster
All rights reserved.

ThorWorks Industries, Inc.
P.O. Box 2277
Sandusky, OH 44870

Phone: 1-800-326-1994 FAX: 1-419-626-5477 www.sportmaster.net

Free estimates

Planning a court or a surface?

Industrial Surface is a SportMaster authorized installer in Northeast Ohio. Send the address and what you have in mind; we walk the site, measure it, and send a written proposal with the scope spelled out.

The yard

4000 East 86th Street, Cleveland, OH 44105

Off Broadway Avenue, south of downtown, ten minutes from I-77 and I-490.

Serving Cuyahoga, Summit, Lake, Lorain, Medina, Geauga, Portage, Stark and Ashtabula counties. Municipal, school, club, HOA and commercial work; residential courts by the job.