INDUSTRIAL SURFACE

SportMaster · Engineering specification

SkateMaster Coating System for in-line hockey

SportMaster's engineering specification, CMT-34, for applying the SkateMaster Coating System for in-line hockey over asphalt. New asphalt cures 14 to 30 days; cracks are filled, depressions 1/8 inch or deeper leveled and one or two coats of Acrylic Resurfacer applied, then a final coat of tinted Neutral Acrylic Resurfacer with 70-90 mesh sand. A minimum of two coats of SkateMaster coating follows, with lines laid out to The National In-Line Hockey Association guidelines and a minimum of one coat of Line Paint.

CMT-34 Revised August 2024 1 page, 74 KB

Open the PDF Ask us about it

This is SportMaster's document, kept here so our customers and crews can read it beside our own pages. SportMaster's own copy is on sportmaster.net.

First page of the SportMaster engineering specification for SkateMaster Coating System for in-line hockey Open the PDF (1 page, 74 KB)

Key facts

SystemSkateMaster Coating System for In-Line Hockey
SurfaceAsphalt
Cure before coatingNew asphalt: 14 to 30 days
Final resurfacer coatTinted Neutral Acrylic Resurfacer with 70-90 mesh sand
Color coatsA minimum of two coats of SkateMaster coating
Line markingLaid out according to The National In-Line Hockey Association guidelines

Taken from this document. The PDF is SportMaster's official document (CMT-34, revised August 2024).

The full text of this document

This is the document's own text, moved from the PDF by machine, word for word, and checked against it. The PDF is SportMaster's official document (CMT-34, revised August 2024). If the two ever differ, the PDF is right.

REVISED 08/24 · Engineering Spec Sheet

Specifications for applying the

SKATEMASTER COATING SYSTEM

for In-Line HockeyCMT-34

PRODUCT NAME

SkateMaster Coating System for In-Line Hockey

DISTRIBUTION LOCATIONS

SportMaster products are distributed through a worldwide network of stores and distributors. Call (800)395-7325 or visit www.sportmaster.net to find a location near you.

1. SCOPE:

1.1 The following specifications pertain to the application of the SkateMaster Coating System for In-Line Hockey. Refer to Product Technical Data sheets for specific mixing and application instructions.

1.2 SportMaster color coating systems are designed for use on properly built sport surfaces. Refer to the American Sports Builders Association for recommended guidelines on construction of athletic & recreational surfaces.

2. SURFACE PREPARATION:

2.1 New Asphalt surfaces must cure 14 to 30 days prior to application. The surface must be cleaned entirely of dust, dirt, debris, and all loose materials.

2.2 Fill all cracks with SportMaster Crack Magic, Acrylic Crack Patch, Acrylic Patch Binder or other suitable crack filler.

2.3 Level depressions or “bird baths” (1/8 inch or deeper) with SportMaster Acrylic Patch Binder or Acrylic Resurfacer patching mix.

2.4 Apply one or two coats of SportMaster Acrylic Resurfacer, as required by surface roughness and porosity, to provide a smooth underlayment for application of the SkateMaster Coating System. A minimum of 2 coats are recommended on new asphalt surfaces. After pavement voids are filled, apply a final coat of tinted Neutral Acrylic Resurfacer with 70-90 mesh sand, per data sheet.

3. APPLICATION OF SKATEMASTER SYSTEM:

3.1 Over properly prepared asphalt, surface apply a minimum of two coats of SkateMaster coating in accordance with manufacturer’s mixing and application instructions.

4. LINE MARKINGS:

4.1 Line markings shall be laid out according to The National In-Line Hockey Association guidelines.

4.2 After masking tape has been laid, apply SportMaster Stripe Rite line primer to seal voids between masking tape and court surface to prevent “bleed under” when SportMaster Line Paint is applied.

4.3 Apply a minimum of one coat of SportMaster Line Paint.

5. GENERAL:

5.1 All work shall be performed in a workmanlike manner. All containers and debris shall be removed from job when completed.

Copyright© 2024, SportMaster
All rights reserved.

ThorWorks Industries, Inc.
P.O. Box 2277
Sandusky, OH 44870

Phone: 1-800-326-1994 FAX: 1-419-626-5477 www.sportmaster.net

Free estimates

Planning a court or a surface?

Industrial Surface is a SportMaster authorized installer in Northeast Ohio. Send the address and what you have in mind; we walk the site, measure it, and send a written proposal with the scope spelled out.

The yard

4000 East 86th Street, Cleveland, OH 44105

Off Broadway Avenue, south of downtown, ten minutes from I-77 and I-490.

Serving Cuyahoga, Summit, Lake, Lorain, Medina, Geauga, Portage, Stark and Ashtabula counties. Municipal, school, club, HOA and commercial work; residential courts by the job.