SportMaster · Guide
10 best practices of repairing and resurfacing tennis and basketball courts
Ten points SportMaster sets out for repairing and resurfacing tennis and basketball courts, from construction to upkeep. They give slope of .8333% - 1.0%, a 10 mil vapor barrier under concrete, cure times of 28 days for concrete and 30 days recommended for asphalt, patching puddles that cover a 5-cent piece 1 Hour after rain, and filling cracks over 1/8” wide. Coatings go on at 50 degrees and rising, unthinned, with the right tools, squeegee technique, masking tape and Stripe Rite, and courts are cleaned regularly.
2 pages, 54 KB
This is SportMaster's document, kept here so our customers and crews can read it beside our own pages. SportMaster's own copy is on sportmaster.net.
Key facts
| Slope | .8333% - 1.0% |
|---|---|
| Cure before coating | 28 days for concrete |
| Vapor barrier under concrete | 10 mil thickness recommended |
| Puddle check | 1 Hour after rain, outline puddles that cover a 5-cent piece and patch with Acrylic Patch Binder patching mix |
| Cracks | Fill all cracks over 1/8” wide with an acrylic-based crack sealant |
| Application temperature | 50 degrees and rising |
Taken from this document. The PDF is SportMaster's official document.
The document, 2 pages
This document is read from its lists and columns, so it is shown here exactly as printed, page by page. Select a page to open the PDF there. The PDF is SportMaster's official document.
The sheet as plain text
The same sheet as text, taken from the PDF by machine with every column left where it stands. It is here for searching, for copying and for screen readers; read the tables from the pages above.
Show the plain text (2 pages)
Page 1
10 Best Practices of Repairing & Resurfacing Tennis & Basketball Courts
1. Longevity and performance of color coating systems are dependent on proper construction
of the court. Consult the ASBA (American Sports Builders Association) website for detailed guidelines
at sportsbuilders.org
• Proper slope requirements are .8333% - 1.0%
• Adequate surface and subsurface drainage should be installed to prevent water accumulation
beneath the surface.
• Concrete courts should have a vapor barrier installed beneath the slab
(10 mil thickness recommended).
• Concrete Courts should be finished with a medium-broom texture, and no curing compounds
should be used.
• Consult the coating manufacturer’s specifications and guidelines for full concrete
preparation instructions.
2. Make sure that new asphalt or concrete is fully cured
• 28 days for concrete
• 30 days recommended for asphalt (during prime curing conditions of moderate sun to draw out oils and rain
to rinse away).
• Make sure that the existing surface is not coated with a pavement sealer. Acrylics do not bond
well to coal tar or most asphalt-based sealants.
3. Surface Repair
• 1 Hour after a rain or flooding the court, outline any puddle areas with chalk that cover a
5-cent piece (American coin). These areas should be repaired with Acrylic Patch Binder patching mix.
• Fill all cracks over 1/8” wide with a suitable acrylic-based crack sealant. Never use a hot or cold
applied asphalt-based crack filler.
4. Clean the court surface prior to application of repair products or coatings. Any areas where
mold, mildew, or fungus is evident should be treated with a solution of 2 parts water to 1
part household bleach. Spray and broom in the bleach solution and allow it to sit for 20 to
30 minutes. Scrub with brooms or suitable equipment, then rinse thoroughly with a pressure
washer. It’s a good idea to treat any areas exposed to shade with this method.
5. Always follow the manufacturer’s mixing instructions. Never over-dilute the coatings in
order to “stretch” coverage. The specified sand size and shape are very important to the look
and performance (speed of play) of the surface. If the proper sand types are not available in your
area, purchase the coatings directly from the manufacturer with sand pre-added.
6. Follow the manufacturer’s application and curing temperatures
• Apply products when temperatures are 50 degrees and rising
• The best time to apply is in the morning when the surface is cooler. If application during hot
temperatures is unavoidable, the surface can be lightly misted to cool the pavement. Do not
puddle. Use a garden pump sprayer or a hose nozzle with mist setting.
• Acrylic Resurfacer and Color Coatings normally dry within 1 hour of application in the full sun (based
on 75° day with low humidity). Shade, low temperatures, and high humidity can increase drying times.
7. Use the proper tools and equipment for mixing and application:
• Floor Scrapers: Use to scrape foreign objects off of the surface prior to application, and gently
scrape the surface between coats to remove small bumps and imperfections. Do not scrape
the finish coat.Page 2
• Grass Trimmers: Trim around the court to prevent grass and weeds from hanging into the
application path.
• Blowers & Brooms: Blow, broom, and gently scrape between coats.
• Pressure Washer: Use to prepare surface for color coating system. Blast the dirt and debris out of
cracks and surface voids.
• Sport Squeegee: Make sure to use a squeegee that is designed for sport surfacing to minimize
squeegee marks on the surface. A rubber blade that is 50 to 60 durometer (measure of softness)
with a tapered/rounded edge is ideal.
• Drill and Paddle Mixer: A 1 to 1.5 horsepower drill is recommended. Agitated tank systems are
also available.
• Line Taping Machine
8. Proper Application Technique
• Watch the SportMaster application video or consult a SportMaster representative for proper
application techniques
• Have enough materials mixed for the entire coat before starting application.
• Never squeegee the entire windrow dry during application, and make sure to pour the material
directly into the existing wet puddle to minimize pour marks on the surface.
• When applying the material by squeegee, only pull about ¼ of the entire width of the squeegee
head. Pulling too much material at once can make it difficult to apply the coatings to the desired
thickness.
• Avoid putting the wet squeegee blade down on a dry, hot surface. Many times the squeegee blade
lines can be seen through the finish coats. This is the same for wet shoes during application, so try
to avoid stepping in the coating windrow.
9. Always use a good quality masking tape for line striping, along with Stripe Rite line primer.
This will minimize bleed under of the line paint for sharp lines. Two-inch wide masking tape
is recommended for tennis court striping. One-inch tape works best for circles and arcs. The
narrower tape can curve better without billowing.
10. SportMaster 100% acrylic sport surfaces require very little maintenance. However, general
cleaning will go a long way to extending the life of the surface.
• Clean the court regularly: Once a month is suggested. Watch for evidence of mold or mildew in
shaded areas and corners where organic debris tends to accumulate. Indoor courts require both
frequent vacuuming and at least one annual wet vacuuming with mild detergent solution and soft
bristled equipment.
• Remove Standing Water: Rain showers help clean your court. However, dirt accumulates in standing
water, leaving stains. Remove water from birdbaths as often as possible. Irrigation systems around
the court should not spray on the court.
• Remove foreign matter: Leaves and pine needles not only can stain your court, but also are
breeding grounds for mold and mildew. It is especially important to remove leaves in the fall and
keep your court free of debris all winter.
• Use proper equipment: Use soft nylon or hair-type brooms for scrubbing your surface. Scrubbing
too hard with hard bristles can damage the surface. When using a water broom, limit pressure to
70 p.s.i. Be very careful when using a power washer. Free estimates
Planning a court or a surface?
Industrial Surface is a SportMaster authorized installer in Northeast Ohio. Send the address and what you have in mind; we walk the site, measure it, and send a written proposal with the scope spelled out.
The yard
4000 East 86th Street, Cleveland, OH 44105
Off Broadway Avenue, south of downtown, ten minutes from I-77 and I-490.
Serving Cuyahoga, Summit, Lake, Lorain, Medina, Geauga, Portage, Stark and Ashtabula counties. Municipal, school, club, HOA and commercial work; residential courts by the job.