INDUSTRIAL SURFACE

SportMaster · Engineering specification

Color coating systems over concrete

SportMaster's engineering specification, CMT-25, for applying its color coating systems over concrete sport surfaces. The slab needs a vapor barrier, perimeter drainage and moisture curing only; new concrete cures 28 days and takes a medium broom finish or a CSP 3 or 4 shot blast profile. Then come acid etching, crack and spall repair, Acrylic Adhesion Promoter, one (1) or more coats of Acrylic Resurfacer, a minimum of two color coats and a minimum of one coat of Line Paint.

CMT-25 Revised May 2024 2 pages, 122 KB

Open the PDF Ask us about it

This is SportMaster's document, kept here so our customers and crews can read it beside our own pages. SportMaster's own copy is on sportmaster.net.

First page of the SportMaster engineering specification for Color coating systems over concrete Open the PDF (2 pages, 122 KB)

Key facts

SystemSportMaster Color Coating Systems
SurfaceConcrete, medium broom finish or similar roughened texture, never steel trowelled
Cure before coatingNew concrete: 28 days
PrimerAcrylic Adhesion Promoter or suitable primer over new or uncoated surfaces
Color coatsA minimum of two coats of Color Concentrate or ColorPlus System
Line markingLaid out to United States Tennis Association specifications

Taken from this document. The PDF is SportMaster's official document (CMT-25, revised May 2024).

The full text of this document

This is the document's own text, moved from the PDF by machine, word for word, and checked against it. The PDF is SportMaster's official document (CMT-25, revised May 2024). If the two ever differ, the PDF is right.

REVISED 05/24 · Engineering Spec Sheet · Specifications for applying · SPORTMASTER COLOR COATING SYSTEMS · over Concrete Sport Surfaces · CMT-25

PRODUCT NAME

SportMaster Color Coating Systems over concrete sport surfaces.

DISTRIBUTION LOCATIONS

SportMaster products are distributed through a worldwide network of stores and distributors. Call (800)395-7325 or visit www.sportmaster.net to find a location near you.

1. SCOPE:

1.1 The following specifications pertain to the application of SportMaster Color Coating Systems over concrete sport surfaces. Refer to Product Technical Data sheets for specific mixing and application instructions.

1.2 SportMaster color coating systems are designed for use on properly built sport surfaces. Refer to the American Sports Builders Association for recommended guidelines on construction of athletic & recreational surfaces.

1.3 The concrete surface must be constructed with a suitable vapor barrier beneath the slab and adequate perimeter drainage to prevent moisture accumulation beneath the surface. Do not use curing compounds on the concrete surface. Moisture curing only.

2. SURFACE PREPARATION:

2.1 New concrete surfaces must cure 28 days. Concrete surfaces should have a medium broom finish or similar roughened texture. They must never be steel trowelled. If using a shot blaster to achieve texture, a shot blast profile of CSP 3 or 4 is recommended.

2.2 Thoroughly remove all dust, dirt, debris and loose materials.

2.3 Etch concrete surface with phosphoric or muriatic acid solution. Rinse clean with water after etching is complete.

2.4 Fill all cracks with SportMaster CrackMagic, Acrylic Crack Patch, Acrylic Patch Binder or other suitable crack fillers.

2.5 Repair spalled areas and level depressions or “bird baths” (1/8 inch or deeper) with SportMaster Acrylic Patch Binder or Acrylic Resurfacer patching mix.

2.6 Apply SportMaster Acrylic Adhesion Promoter or suitable primer over new or uncoated surfaces.

2.7 Apply one (1) or more coats of Acrylic Resurfacer to provide a smooth underlayment for application of the SportMaster Color System.

3. APPLICATION OF SPORTMASTER COLOR SYSTEM:

3.1 Over properly prepared concrete surface, apply a minimum of two coats of SportMaster Color Concentrate or ColorPlus System in accordance with manufacturer’s mixing and application instructions.

4. LINE MARKINGS:

4.1 Line markings shall be laid out according to United States Tennis Association specifications.

4.2 After masking tape has been laid, apply SportMaster Stripe Rite line primer to seal voids between masking tape and court surface to prevent “bleed under” when SportMaster Line Paint is applied.

4.3 Apply a minimum of one coat of SportMaster Line Paint.

5. GENERAL:

5.1 All work shall be performed in a workmanlike manner. All containers and debris shall be removed from job when completed.

Page 2

Copyright© 2020, SportMaster
All rights reserved.

ThorWorks Industries, Inc.
P.O. Box 2277
Sandusky, OH 44870

Phone: 1-800-326-1994 FAX: 1-419-626-5477 www.sportmaster.net

Free estimates

Planning a court or a surface?

Industrial Surface is a SportMaster authorized installer in Northeast Ohio. Send the address and what you have in mind; we walk the site, measure it, and send a written proposal with the scope spelled out.

The yard

4000 East 86th Street, Cleveland, OH 44105

Off Broadway Avenue, south of downtown, ten minutes from I-77 and I-490.

Serving Cuyahoga, Summit, Lake, Lorain, Medina, Geauga, Portage, Stark and Ashtabula counties. Municipal, school, club, HOA and commercial work; residential courts by the job.